SmokeLuvr1971
New Member
Pickaxe worked well for me [I usually silky-ify as soon as possible...dunno if that matters]. Imagine TiCo Hammer would work as well.
-
The FTB Forum is now read-only, and is here as an archive. To participate in our community discussions, please join our Discord! https://ftb.team/discord
[1.6.4]Crash Landing [Hardcore, HQM] version 1.1.x BETA STABLE
- Thread starter Iskandar
- Start date
FallenS0ul
New Member
SmokeLuvr1971
New Member
Raid some TiCo buildings for Cobalt Ingots [you only need 2]. Turn one into a pickaxe head and the other into 2 tool rods. Affix these onto your current pickaxe.All my tools take "forever" to break them
FallenS0ul
New Member
Oooh cobalt is fast? Im using manylln? however u spell that.
Cobalt is the fastest in the game.
FallenS0ul
New Member
Meh i thought manylyylyl was the best
There is a durability tradeoff I believe.
SmokeLuvr1971
New Member
IIRC:
Cobalt for Speed/Mining Level
Manyullyn? for Durability
Edit: Aside - if using cobalt for the 'repair' part of the tool, I'd suggest you also install a battery modifier...since Nether ores aren't all that easy to come by reliably [depending on where you are in the tech tree].
This process/setup can even be done early game [and helps smash spawners quickly]. Cobalt from city raiding/soul sand sifting. Use machine frame quest reward to build Energetic Infuser. Place the Infuser atop a Hardened Energy cell, which is powered via 4 Survivalist Gens.
Last edited:
pc_assassin
New Member
Cobalt is fastest but I think man is the sharpest
Sent From Something That You Won't Care About Using Tapatalk 2
SmokeLuvr1971
New Member
Yup. Just checked the 'unofficial' wiki.
Cobalt - Speed/Mining Level
Manyullyn - Damage/Durability
For some reason my SFM is not taking the steam and pumping it into the Turbine. I followed your imgur but still cant get it to work. Any ideas?
Henry Link
Forum Addict
You need to make him op. Next time you setup the game and open it to the LAN type in /op <playername>
Once you do that he should be able to use the /hqm commands.
This is wrong. Manyullyn is best all around. I believe you are thinking of the comparison between cobalt and ardite. Cobalt for mining speed, Ardite for durability[DOUBLEPOST=1413492191][/DOUBLEPOST]
ok, did you right click one of the reactor coolant ports so its red, and that it is aligned directly below a turbine fluid port(also red).
If so, could I see a few screenshots of your SFM 'program'
pc_assassin
New Member
No cobalt has I think a .5 difference in speed or maybe it was 1 more I'm not sure but if you read through materiels and you its there
Sent From Something That You Won't Care About Using Tapatalk 2
Sent From Something That You Won't Care About Using Tapatalk 2
Unless something has been changed by Iguana Tweaks, cobalt has always had faster mining speed than manyullyn. Like 1-2 levels faster.
SmokeLuvr1971
New Member
I was going off the numbers listed in the 'unofficial' wiki page for TiCo materials. I also recall having a Manyullyn pickaxe [head] that performed faster after downgrading to a cobalt head. I also tried to find some info on the 'official' wiki but...there isn't any [gasp!]. Good to see the unofficial wiki TiCo infos are still accurate [mostly]. The only inaccuracy I've seen are the Green/Blue slime parts [they should be swapped].
@ttech Small checks:
Did you right click one of the reactor coolant ports so its red, and that it is aligned directly below a turbine fluid port(also red).
Did you right click one of the turbine coolant ports so its blue, and that it is aligned directly above a reactor coolant port(also blue/cyan)
Point your cross-hairs at the redstone emitter and press shift. Do you see all but "up" toggling between 0 and 15? If not disconnect "t:Check" from the condition, break the emitter and replace it, work from the back-end of your SFM 'program' to the start reselecting the emitter where needed, then reconnect "t:Check". After a few moments(2ish seconds) the emitter should rapidly pulse.
Did you right click one of the reactor coolant ports so its red, and that it is aligned directly below a turbine fluid port(also red).
Did you right click one of the turbine coolant ports so its blue, and that it is aligned directly above a reactor coolant port(also blue/cyan)
Point your cross-hairs at the redstone emitter and press shift. Do you see all but "up" toggling between 0 and 15? If not disconnect "t:Check" from the condition, break the emitter and replace it, work from the back-end of your SFM 'program' to the start reselecting the emitter where needed, then reconnect "t:Check". After a few moments(2ish seconds) the emitter should rapidly pulse.
Last edited:
The SFM looks fine unless the ports you are using in SFM for steam are actually those that are handling water and vice-versa.
Also, did you activate the turbine?
If so, can I get a world download? (Stand infront of reactor, exit minecraft. locate your crashlanding folder, navigate to ../crashlanding/minecraft/saves/, zip your world's save file, post it to a website and give link)