• The FTB Forum is now read-only, and is here as an archive. To participate in our community discussions, please join our Discord! https://ftb.team/discord

Problem With Ender Quarries and Thermal Dynamics (Infinity Evolved)

  • Thread starter Thread starter SvenShiro
  • Start date Start date
S

SvenShiro

Guest
So basically for a quick rundown my issue is that when I switch all my pipes to thermal dynamics rather than BC transport my Ender quarries stopped mining, like at all... The reason I did this is because I have 4 Ender quarries going in the deep dark and all the items were going back to one tesseract where they are sorted. Ores go through a sag mill and then through an alloy smelter (if there is a better way to do that please enlighten me). Other matierials just go straight into my ME system while others are deleted and I also have cobblestone going through autocrafters to be compressed before it goes into my ME system. The problem started happening when I started upgrading everything my Ender quarries started getting faster and my gold pipes starting blowing up when I booted up my reactor because too many items where going through. After this I decided to switch to those warp pipes from thermal dynamics. Now I'm sitting here scratching my head because my Ender quarries just sit there eating power and not mining. Anyone have any ideas?
 
SvenShiro said:
So basically for a quick rundown my issue is that when I switch all my pipes to thermal dynamics rather than BC transport my Ender quarries stopped mining, like at all... The reason I did this is because I have 4 Ender quarries going in the deep dark and all the items were going back to one tesseract where they are sorted. Ores go through a sag mill and then through an alloy smelter (if there is a better way to do that please enlighten me). Other matierials just go straight into my ME system while others are deleted and I also have cobblestone going through autocrafters to be compressed before it goes into my ME system. The problem started happening when I started upgrading everything my Ender quarries started getting faster and my gold pipes starting blowing up when I booted up my reactor because too many items where going through. After this I decided to switch to those warp pipes from thermal dynamics. Now I'm sitting here scratching my head because my Ender quarries just sit there eating power and not mining. Anyone have any ideas?
Click to expand...
Yes - you're going to need Servos. They come in different levels, including hardened and resonant, and go on the wide bit of itemduct on the side of what it's connected to.

I suspect your quarry is backstuffed with items, basically.

Ooh actually - don't warpducts need power? Have you tried a lower tier duct?

EDIT: from one of the wikis

"The Warp Itemduct is a block added by the Thermal Dynamics mod. An energised Itemduct that moves items instantly. It requires 800 RF per length to activate and consumes 50 RF per stack transported."
 
I need a Servos connected to my Ender Quarry? and I have power to all my warp ducts so don't worry about that
 
Do Ender quarries have actual inventories? I've always been under the impression they just spit items out when they mine them
 
SvenShiro said:
I need a Servos connected to my Ender Quarry? and I have power to all my warp ducts so don't worry about that
Click to expand...

It goes on the end of the duct. The Ender quarry will auto-output to some things, but it may not do so for the ducts, in which case you need a servo on the pipe at the quarry end, or a Retriever at your destination end.

That's what I'm wondering - if it has nowhere to go, but it thinks it SHOULD be able to put something there and can't, it gets stuck?
 
From the gamepedia wiki entry on the Ender quarry:

"If the Quarry has completed, or has nowhere to put items, it will stop running, but continue to draw power."
 
Well if anything was that easy that would explain my issue but I just hooked up a servo to my Ender Quarry and the quarry is still just sitting there
 
Is there any other kind of pipes I could use in this game besides thermal dynamics pipes?
 
Yes I guess I will have to try those, unfortunately I have to leave my computer at a bad time right now though. When I get back I will try that though
 
Just one thing before I leave every time I go into the deep dark and then come back all my fuel is my reactor is gone, is this a bug or something?
 
yes I have a world anchor next to my reactor, that was my initial thought as well and then I put the world anchor there but it didn't fix it
 
I can already tell ender io item conduit won't work because it has no way to tell it which way to send items, like diamond pipe in BC Transport
 
You use the Yeta Wrench to set the connection points to Extract (for the quarry) and insert (for the destination) and they do the rest.

You can filter by adding filters into those connection points.
 
I just can't seem to get the ender quarries to mine, even if I put the tesseract right next to it like I was before
 
went back to bc transport just to see what would happen, they started mining....what
 
SvenShiro said:
I just can't seem to get the ender quarries to mine, even if I put the tesseract right next to it like I was before
Click to expand...
Definitely something skewiff about that. Could be buggy. Have you got it set to replace with dirt (default) or to void out the area?

EDIT: ok? That's just weird.
 
Lmao I'm running out of ideas here, if only this stupid pipe didn't blow up instantly...
 
I placed two vacuum chests down to collect all the items on the floor that come out of the pipe when it blew up, They both filled up instantly and there's still items on the floor.....
 
You must log in or register to reply here.
Back
Top