Search results

I actually sat through an hour video on youtube and discovered that yes, I needed the speed upgrade, I just came back and saw the same response here X3 It is now working PERFECTLY and sitting at a nice 1775 RPM now... thanks!

So a few weeks back I was having an issue involving big reactors turbines. I cannot get my turbine to play nicely with my reactor. My setup: 5x5 reactor with a single, centered fuel rod, 3 tall. Produces 1800mB/t Steam 2 extra utilities transfer nodes (liquids), and pipes transferring the...

According to the official website (http://www.technicpack.net/modpack/tekkitmain.552547) they are actually, in fact, in version 1.2.9g, which... following the alphabet, I am willing to bet is 1 version after 1.2.9f, in which case this: Is, in fact, accurate. I will be combing through the...

See, you say that, but this is a version that me and my 'mates just downloaded a little over a week ago... there has been only one update (that I have been notified of) since then, however I have not implemented it yet until all of us can agree that we want to upgrade the server first. So...

Tekkit 1.2.9f That said, this doesn't seem like a 'debugging' problem, it seems more like I might have something set up incorrectly. I have made different turbines before (one specifically at 2000mB/t) that work fine, it is just this design that is, for some reason, faulty.

As you can see, I do not have that part of the UI, as I said. Mine is likely an out of date version (though a version I wish to keep, as the server I am playing on hasn't updated yet).

If this is the case, then my setup for piping seems to be correct. It is set to pipe 2000mB/t of liquid via the transfer nodes (2 of them), and it seems that when it pulls this steam and runs it for a tick... there IS 200mB of steam left in the tank after said tick (hence, it is using 1800mB/t...

Above 'exhaust options' is 'Max flow', which, as I mentioned, is set to 1800mB/t (coinciding with the reactor), and I have attempted to lower this, to no effect as for blades used and coil material, my calculations are above, which are the minimum and most efficient methods of arriving at...

I have done this already, the turbine has been set since the start to use the max output of 1800mB/t (the same value my reactor is producing). I have also tried lowering this, to no effect.

I do not see this anywhere, I only see the toggles for whether the turbine is active or not, and whether or not it should or should not dump exhaust. I also cannot find reference to this in any of the wikis. I did, however, try removing the coils except 1 block of enderium, to no beneficial...

How do I do this? just remove the coils from the machine? Or is there some UI I have not discovered? And I literally meant real life days to spin up... I ran it for 4 hours and it was still increasing, though it only got to 50 rpm in that time. I highly doubt that that kind of wait is an...

Ok, I have temperature under control now... there is yet another problem though (lucky me). Though the turbine is spinning and converting steam into water now, the spinup for it is HORRENDOUSLY slow, like, I would have to run this thing for DAYS to get to 900RPM... why? It is recieving enough...

k, thanks for the help. I seem to be having some issues. it seems that my system is jammed now. While they should be exchanging water and steam at the same rate (in my setup, 1800mB/t), they are instead saying 'the reactor is full, so I can't send it water' 'the turbine is full, so I can't...

So it sounds as if the transfer pipes are, in fact, better than the fluiducts. Is it possible that the transfer pipes use the same speed as the transfer nodes (1000mB/t or 1B/t)?

I need to pipe large amounts of liquids into a big reactors setup (reactor AND turbine), and was wondering what would be the best setup of pipe and water generation to use... the problem is, I cannot find information regarding the extra utilities piping speeds. Fluiducts pipe 100mB/t per...